top of page
MODEL X

Eclipson Model X is an extremely efficient 2 meters wingspan UAV platform. The aerodynamics have been carefully analyzed during the initial design phase with one main objective: to fly further with less energy consumption. The model is very stable and easy to launch with or without power. The wings are detachable to facilitate easy transportation.  There are 2 versions provided: one with flaps and one without. You can choose which depending mainly on your available landing area.  Its fuselage has a huge internal space which can be accessed easily via 3 canopies.  This will enable a variety of electronics to be installed, such as flight controllers, solar powered electrics, FPV equipment, pitot tubes etc., depending upon your requirements.

Includes:
-STL files

-G-codes

-Scheme design

For free:

-UAV holders

€39

Features:
-Big internal space
-Very efficient
-Easy to launch

SPECIFICATIONS

PRINTED WEIGHT              860 g
MIN TAKE OFF WEIGHT      1400 g 
MAX TAKE OFF WEIGHT      1800 g

STALL SPEED                    28km/h        
MIN WING LOADING           37g/dm²   

WING SPAN                 2000mm
WING SURFACE            38dm²
WING ASPECT RATIO    10
LENGTH                      1150mm

Note: It is required the use of LW-PLA for this model.

ARRANGEMENT DRAWING AND PRINTING PARAMETERS

Printing_parameters_.jpg

SHOPPING LIST

ALL THE COMPONENTS THAT YOU HAVE TO BUY TO FLY THE AIRPLANE

3D PRINTER
MIN PRINTING VOLUME - 170x170X200 (X,Y,Z)
NOZZLE DIAMETER - 0,4 mm


Recommended

FILAMENT
QUANTITY 
350g
(LW-PLA)
500g (PLA)
10
g (TPU)

Recommended

colorfabb.JPG

ECLIPSON STANDARD POWER PACK
SERVOS NEEDED - x6

Recommended

Use folding propeller:
Folding prop 8x6

Captura.PNG

BATTERY
VOLTAGE - 11,1V (3S)
CAPACITY - 2200 mAh to 6000 mAh

*If the weight of the battery is less than 300 g it will be necessary to add lead in the nose of the aircraft

Recommended
BAT4

bat4.jpg

RADIO CONTROL SYSTEM
MIN CHANNELS - 7CH

Recommended

Captura.JPG

OTHER PARTS
-PUSH RODS - D1,2mm (min length 250mm)  2units
-STEEL ROD - D2mm (Length 25mm) 1units
-CF TUBE - D6mm (Length 660mm) 2units
-CF TUBE - D8mm (Length 835mm) 1units
-CF TUBE - D8mm (Length 600mm) 1units
-CF TUBE - D8mm (Length 550mm) 2units
-CF ROD - D1mm (Length 650
mm) 2units
-BOLT - M3X15mm (with nuts and washers)  4units
-BOLT - M3X20mm (with nuts) 2units

-SCREW - M2X8mm (aprox) 27units
-GLUE - cyanoacrylate
-PUSH RODS CONNECTORS  6units
-RUBBER BAND- L50mm (aprox.)
-VELCRO
-SERVO LEAD EXTENSION (
min 400mm) 4 units

Recommended

UAV HOLDERS

DOWNLOAD FOR FREE THE LATEST HOLDERS FOR MODEL X

Printing_parameters_FPV.jpg

WOULD YOU LIKE TO CUSTOMIZE YOUR OWN UAV HOLDER AND GET ANOTHER  ECLIPSON MODEL FOR FREE?

Model X has a big fuselage where you can allocate many electronic components: FPV cameras, Flight controllers, pitot tubes etc... If you have some design knowledge and you have a good idea to upgrade or to create a new holder for any specific equipment, we invite you to use the included STP files to make your mod, test it, take some pictures and then contact us or post it on our Facebook group. If your design is selected we will give you a coupon code to receive any other Eclipson model for free. Furthermore, your design will be shared for free here with our community.

UAV holders Model X
Eclipson 3d printed aircraft
Subs
bottom of page